Filter
Sort:
Show:
1″ BRASS AIR BLEEDING VALVE,PN16
Add to Wishlist
Add to Wishlist
Compare

1″ BRASS AIR BLEEDING VALVE,PN16

AED 60.00
In Stock
The 1 inch Brass Air Bleeding Valve PN16 (also known as an Automatic Air Vent) is a critical safety and efficiency component for hydronic piping systems. Its primary function is to automatically exhaust trapped air from a system while it is filling with water and to continue bleeding air bubbles that release during operation. Removing air is essential to prevent "air locking," reduce noise (gurgling), and protect components like pumps and radiators from cavitation and corrosion.
Add to cart
Add to Wishlist
Add to Wishlist
1″ BRASS PRESSURE RED. VALVE PN16 THRD
Add to Wishlist
Add to Wishlist
Compare

1″ BRASS PRESSURE RED. VALVE PN16 THRD

AED 115.00
In Stock
The 1 inch Brass Pressure Red. Valve PN16 Thrd Mech is an automatic control valve designed to reduce a high, fluctuating inlet pressure to a lower, constant outlet pressure. This is a critical component for protecting downstream plumbing fixtures, water heaters, and appliances from the potential damage caused by excessive municipal water pressure. Its PN16 rating ensures it can safely handle inlet surges up to 16 bar.
Add to cart
Add to Wishlist
Add to Wishlist
2″ BRASS CHECK VALVE PN16 THRD
Add to Wishlist
Add to Wishlist
Compare

2″ BRASS CHECK VALVE PN16 THRD

AED 140.00
In Stock
The 2 inch Brass Check Valve PN16 Thrd Mech is an essential safety component designed to prevent backflow in piping systems. This unidirectional valve allows fluid to flow in one direction and automatically closes if the flow reverses, protecting pumps and equipment from water hammer and contamination. Its PN16 rating makes it a robust choice for domestic water boosters, heating circuits, and industrial process lines.
Add to cart
Add to Wishlist
Add to Wishlist
2″ BRASS BALL VALVE PN16 THRD
Add to Wishlist
Add to Wishlist
Compare

2″ BRASS BALL VALVE PN16 THRD

AED 135.00
In Stock
The 2 inch Brass Ball Valve PN16 Thrd Mech is a high-capacity manual isolation valve designed for rapid quarter-turn operation. Featuring a full-bore design, this valve allows for maximum flow volume with minimal pressure drop, making it ideal for main water lines, industrial plumbing, and HVAC systems. The forged brass body provides superior strength and pressure resistance compared to cast alternatives.
Add to cart
Add to Wishlist
Add to Wishlist
1″ BRASS LOCK GATE VALVE PN16 THRD W/O KEY
Add to Wishlist
Add to Wishlist
Compare

1″ BRASS LOCK GATE VALVE PN16 THRD W/O KEY

AED 54.00
In Stock
The 1 inch Brass Lock Gate Valve PN16 Thrd W/O Key Mech is a specialized security valve designed to prevent unauthorized operation or tampering of water and gas supplies. Unlike standard gate valves, this model features a modified stem or handle housing that can be locked in the open or closed position. This specific version is supplied without the key, typically intended as a replacement unit or for use in systems where a master key is already present.
Add to cart
Add to Wishlist
Add to Wishlist
2″ BRASS GATE VALVE PN16 THRD
Add to Wishlist
Add to Wishlist
Compare

2″ BRASS GATE VALVE PN16 THRD

AED 120.00
In Stock
The 2 inch Brass Gate Valve PN16 Thrd Mech is a reliable, full-port isolation valve designed for residential, commercial, and industrial flow control. Crafted from high-quality brass, this valve features a solid wedge design that ensures a positive shut-off and minimal pressure drop when fully open. Its PN16 rating makes it suitable for medium-pressure applications, including domestic water services, heating systems, and compressed air lines.
Add to cart
Add to Wishlist
Add to Wishlist
6″ DI (BS1387) FLANGE ADAPTOR PN16
Add to Wishlist
Add to Wishlist
Compare

6″ DI (BS1387) FLANGE ADAPTOR PN16

AED 60.00
In Stock
The 6 inch DI (BS1387) Flange Adaptor PN16 Mech is a high-performance mechanical fitting designed to connect plain-ended BS 1387 steel pipes to flanged equipment such as valves, pumps, or meters. This adaptor is essential for retrofitting existing systems or installing new infrastructure where welding is not feasible. The mechanical end features a compression-style gasket that provides a leak-proof seal around the pipe exterior, while the flanged end conforms to PN16 drilling standards.
Add to cart
Add to Wishlist
Add to Wishlist
 6″ DI (SCH40) GROOVED FLANGE PN16
Add to Wishlist
Add to Wishlist
Compare

 6″ DI (SCH40) GROOVED FLANGE PN16

AED 72.00
In Stock
The 6 inch di (sch40) grooved flange pn16 mech is a specialized transition fitting designed to join grooved piping systems directly to flanged components such as pumps, valves, and tanks. engineered for schedule 40 steel pipe, this flange adapter provides a secure mechanical connection on one side and a standard pn16 flanged face on the other, eliminating the need for welding or complex pipe fabrication.
Add to cart
Add to Wishlist
Add to Wishlist
1″ GMI UNION CONICAL
Add to Wishlist
Add to Wishlist
Compare

1″ GMI UNION CONICAL

AED 11.00
In Stock
The 1 inch gmi union conical mech is a three-piece galvanized malleable iron fitting designed to allow for the easy connection and disconnection of piping without the need to rotate the pipe. featuring a conical (tapered) metal-to-metal seat, this mechanical union provides a high-pressure seal without the need for a separate gasket, making it ideal for high-temperature or high-vibration fire protection environments.
Add to cart
Add to Wishlist
Add to Wishlist
1″ GMI END CAP
Add to Wishlist
Add to Wishlist
Compare

1″ GMI END CAP

AED 3.00
In Stock
The 1 inch gmi end cap mech is a high-strength galvanized malleable iron fitting designed to provide a secure, leak-proof termination for a 1-inch threaded pipe run. this mechanical end cap is a standard component in fire sprinkler systems and industrial mechanical piping, used to close off the end of a line or to seal branch connections during system pressure testing.
Add to cart
Add to Wishlist
Add to Wishlist
2 1/2″ GMI PLUG
Add to Wishlist
Add to Wishlist
Compare

2 1/2″ GMI PLUG

AED 10.00
In Stock
The 2 1/2 inch gmi plug mech is a high-strength galvanized malleable iron fitting used to permanently or temporarily seal female threaded ports and pipe ends. this mechanical plug is a critical component in fire protection manifolds and industrial piping systems where a secure, pressure-rated closure is required for unused outlets or system testing points.
Add to cart
Add to Wishlist
Add to Wishlist
 2″ X 1″ GMI BUSH
Add to Wishlist
Add to Wishlist
Compare

 2″ X 1″ GMI BUSH

AED 8.00
In Stock
The 2" x 1" gmi bush mech is a compact galvanized malleable iron fitting designed to reduce the size of a female threaded opening. this mechanical hex bushing allows for a direct transition from a 2-inch threaded port down to a 1-inch pipe or fitting, making it an essential component for space-saving connections in fire protection manifolds and industrial plumbing.
Add to cart
Add to Wishlist
Add to Wishlist
1″ X 1/2″ GMI RED SOCKET
Add to Wishlist
Add to Wishlist
Compare

1″ X 1/2″ GMI RED SOCKET

AED 4.00
In Stock
The 1" x 1/2" gmi red socket mech is a precision-engineered galvanized malleable iron fitting used to connect two threaded pipes of different diameters. this reducing socket is a staple in fire protection and mechanical piping systems, specifically used to transition from a 1-inch supply pipe down to a 1/2-inch branch line or sprinkler head connection.
Add to cart
Add to Wishlist
Add to Wishlist
2″ X 3/4″ GMI RED SOCKET
Add to Wishlist
Add to Wishlist
Compare

2″ X 3/4″ GMI RED SOCKET

AED 12.00
In Stock
The 2" x 3/4" gmi red socket mech is a high-quality galvanized malleable iron reducing fitting designed to connect two pipes of different diameters in a straight line. this mechanical socket is commonly utilized in fire protection systems and industrial piping to transition from a 2-inch main line down to a 3/4-inch branch or equipment connection.
Add to cart
Add to Wishlist
Add to Wishlist
 4″ DI GROOVED CROSS TEE
Add to Wishlist
Add to Wishlist
Compare

 4″ DI GROOVED CROSS TEE

AED 90.00
In Stock
The 4 inch di grooved cross tee mech is a high-durability pipe fitting designed to facilitate a four-way intersection within a grooved piping network. commonly utilized in fire protection and industrial mechanical systems, this fitting allows for the distribution of fluid into multiple branch lines from a single junction while maintaining structural integrity and high flow efficiency.
Add to cart
Add to Wishlist
Add to Wishlist
6″ DI (BS1387) GROOVED END CAP
Add to Wishlist
Add to Wishlist
Compare

6″ DI (BS1387) GROOVED END CAP

AED 28.00
In Stock
The 6 inch di (bs1387) grooved end cap mech is a robust pressure-rated fitting designed to provide a secure and leak-proof closure at the end of a grooved piping run. engineered for compatibility with bs 1387 steel pipe dimensions, this end cap is a critical component for fire protection systems, allowing for easy system expansion or maintenance by providing a removable termination point.
Add to cart
Add to Wishlist
Add to Wishlist

Filter Products

Active Filters: Brand: Mech ✕
Brands
Mech ✕
Categories
Services (16)
Extinguisher Refilling Services (14) Hydrostatic Testing (7) FM200 Extinguisher Servicing (2)
Special Sytem (19)
Aspirating Smoke Detection (ASD) System (5) Inert Gas System (1) Water Mist System (1) FM 200 System (3) Kitchen Hood Fire Suppression System (8) Deluge Valve System (1)
Fire Alarm Products (966)
Fire Alarm Detectors (349) Control Panels (162) Panel parts and Spares (4) Detectors (1) Modules & Interfaces (107) Manual Call Point (88) Cables (102) Testing Kits (19) Sounders & Beacons (124)
Battery (43)
Sealed / Maintenance-Free Battery (43)
Emergency lights (124)
Central Battery System CBS (17) Emergency Lights Spare Parts (2) Monitoring System (45) Normal Emergency light (62)
Fire Fighting (528)
Fire Fighting Valves (214) Fire Hose Reels, Fire Hoses & Hydrants (19) Fire Fighting Cabinets (27) Fire Rated Doors (20) Fire Pumps (87) Sprinklers and Covers (27) Fire Fighting Accessories (94)
Fire Extinguishers (53)
Class A - Water Fire Extinguisher (Solid or Mist) (5) Class A, B - Foam Extinguishers (AFFF) (7) Class A, B, C, E - Dry Powder (ABC) (22) Class B, E, C - Carbon Dioxide (CO₂) (13)
Safety Signages (3)
Price Range
AED 0 — AED 152860